How to play Laser Puzzle

Laser Puzzle is a free daily logic puzzle. A laser fires across a grid, and you place mirrors to bend it into the longest path you can. There's a new puzzle every day, and everyone gets the same one.

The goal

Your score is the path length: how many steps the laser takes before it leaves the board or is stopped. When the beam splits, every beam counts.

  • Each puzzle gives you a limited number of mirrors, usually 8 to 11.
  • Click or tap an empty square to place a mirror. Click it again to flip it, and once more to remove it.
  • Hold and drag to erase several mirrors at once.
  • Experiment as much as you like, but you only get one submission per puzzle. Afterwards you'll see how your path compares with the best possible one and with other players.
  • Your best attempt so far is saved. Tap it to put those mirrors back on the board.

Mirrors

A mirror turns the beam 90 degrees. There are two kinds, / and \, and both sides of a mirror reflect, so a beam can come back and bounce off the other side later.

Two mirrors turn the beam down, then left, for a longer path. Path length: 16.

Walls

Grey squares are walls. A beam that hits one stops there, and you can't place mirrors on them. Most of a puzzle is working out how to wind the beam through the gaps.

A wall stops the beam. Steer around it. Path length: 15.

Splitters

A splitter is a triangle. What it does depends on which side the beam hits:

  • The point: the beam splits into two beams that leave at right angles, one each way. Both new beams add to your score, and each gets its own color.
  • A side: the beam turns and leaves through the point.
  • The flat back: the beam stops, as if it hit a wall.
Into the point: the beam splits in two. Path length: 10.
Into a side: the beam turns and leaves through the point. Path length: 11.

One-way gates

A gate has an arrow. A beam travelling the way the arrow points passes straight through, and the gate counts as a step. From any other direction, the gate is a wall.

With the arrow: the beam passes through. Path length: 7.
Against the arrow: the gate is a wall. Path length: 3.

Portals

Portals come in matching pairs, shown by color and shape. A beam that enters one portal comes out of its twin, still heading the same way. Entering costs one step, and the jump itself is free. Portals work from any side and in both directions, and a beam can use the same portal more than once.

Portals are often the only way into a part of the board that walls seal off.

The beam enters one portal and leaves its twin, still heading the same way. Path length: 5.

Collisions

Beams can cross each other at right angles. But when two beams meet head-on they both stop with a spark, and a beam that runs head-on into a path that's already lit stops there. The same goes for two beams hitting the same face of a mirror. With splitters on the board, watch out for beams that cut each other short.

Split beams sent back at each other meet head-on and both stop. Path length: 17.

Strategy tips

  • Find the longest runs first. Before placing anything, look for the longest straight lines on the board, such as rows or columns with no walls in the way. Then work out how to get the beam into each one and out again.
  • Make every mirror earn its place. Long straight runs score the most per mirror, so zigzag across the whole width or height of the board instead of making tight turns.
  • Use the edges and corners. Walls that reach the edge split the board into regions. Plan how the beam will get into each one and back out.
  • Work backwards. Pick where you want the beam to finish, often a far corner, and trace a route back to the laser.
  • Give both split beams somewhere to go. After a splitter, each beam needs its own long route. Make sure they won't run into each other head-on.
  • Check where gates and portals lead. A gate can block a shortcut you were counting on, and a portal is only worth using if the beam has room to run when it comes out.
  • Save your submission. Your best attempt is kept, so try wild ideas before you submit.